Is It Okay To Skip Gears With A Manual Transmission?

Sponsored Posts

Comments

Anonymous

so basically rev match and you’re fine

08/20/2017 - 14:11 |
94 | 0
Black Phillip

In reply to by Anonymous (not verified)

Exactly

08/20/2017 - 21:08 |
2 | 0
Anonymous

Offtop question: In my BMW, when I’m starting off, the shifter is shaking a lot. Why?

08/20/2017 - 16:23 |
0 | 0
El Chloro

In reply to by Anonymous (not verified)

it needs new wires\strings idk how its called but its cheap work below the stick

08/20/2017 - 16:28 |
0 | 0
Anonymous

In reply to by Anonymous (not verified)

Cardan Joint defect?

08/20/2017 - 16:29 |
0 | 0
Anonymous

In reply to by Anonymous (not verified)

Either you’re releasing too fast the clutch or engine and/or transmission mounts may be worn, allowing the powertrain to vibrate.

08/20/2017 - 16:42 |
0 | 0
OktayOe

In reply to by Anonymous (not verified)

Same here but that should be normal imo. Never seen it differently in BMWs

08/20/2017 - 16:51 |
0 | 0
Anonymous

In reply to by Anonymous (not verified)

engine mount or gearbox mount damaged

08/20/2017 - 17:07 |
0 | 0
Anonymous

Just one question, when you downshift, the revs tend to get higher. Can you brake the engine by doing, like, 120KM/H on 5th (around 3.5 k RPM), then to 2nd?

08/20/2017 - 16:51 |
0 | 0
Anonymous

In reply to by Anonymous (not verified)

I’m sorry, can -> could

08/20/2017 - 16:51 |
0 | 0
Anonymous

In reply to by Anonymous (not verified)

Sure! If you want to fry your clutch.

08/20/2017 - 17:05 |
0 | 0
Anonymous

In reply to by Anonymous (not verified)

won’t fry your clutch if you rev match… there’s little to no clutch slip if you rev match correctly. You really don’t want to do it because going down so many gears like that risks over revving the engine.
If your aim of engine braking it to slow down quicker into a corner then don’t do it it’s not worth it, racing instructors will tell you it won’t make you any faster than just getting your braking point right. if the aim is to reduce brake wear in street driving you still shouldn’t do it in that way, you’re better of anticipating when to slow down earlier and just engine brake one gear at a time not 3.

08/20/2017 - 17:20 |
2 | 0
DelF40

In reply to by Anonymous (not verified)

No, but you will definitely brake your transmission. Ever heard of the term “I just blew a tranny”?

08/20/2017 - 17:24 |
0 | 0
Anonymous

I’ve never skip gears when I shift to upper gears, only done when I tried to downshift though, and yes rev matching would really help if you do this. But seriously, its bugging me that people skip gears while upshifting, like why on earth, would you do that?

08/20/2017 - 16:52 |
0 | 0
Anonymous

In reply to by Anonymous (not verified)

Got 6 gears. Don’t need ‘em all. EVERY trucker skips gears.

08/20/2017 - 17:07 |
6 | 0
Anonymous

In reply to by Anonymous (not verified)

I do it quite often.
0-90km/h as fast as possible using gear 1 & 2 and then once you hit 90 you go to 5th to drive normally

08/20/2017 - 17:07 |
6 | 0
nandee

In reply to by Anonymous (not verified)

I usually accelerate upto 60 km/h in the city, and I just skip 4th gear and go into 5th to cruise… Sure, I could go one by one, but sometimes I just don’t.

08/20/2017 - 17:24 |
0 | 0
Jakob

In reply to by Anonymous (not verified)

In a 30 km/h zone, you accelerate in first, then into second and then you are at 30ish km/h. After that, you can just skip third and stay at 30 km/h in fourth to keep the revs nice and low.

08/20/2017 - 18:09 |
0 | 0
Anonymous

In reply to by Anonymous (not verified)

Why on earth would you not?

08/20/2017 - 18:21 |
0 | 0
Anonymous

Funny!
I always thought reving while shifting gears is newbie thing…
I mean it often happened to me when I was learning how to drive
Sometimes I just happened to push clutch before I took my leg off accelerator

08/20/2017 - 17:00 |
0 | 0
Anonymous

In reply to by Anonymous (not verified)

Rev on downshifts, never on upshifts. And after you push the clutch, not because of the clutch.

08/20/2017 - 17:09 |
8 | 0
Anonymous

Shift properly or your car’s chi will be out of balance.

08/20/2017 - 17:29 |
28 | 0
Anonymous

As he has a BMW, He should do a video show BMW drivers how to use turn signals!

08/20/2017 - 17:35 |
0 | 0
Nick Friello

I watched this video and tried shifting from 5th to 2nd on the freeway…and my engine made a horrible noise and won’t start anymore. Did I do something wrong?$?$

08/20/2017 - 17:48 |
0 | 0

Yeah, you used a too short gear for your speed, if you lowrered the Rpm enough you could have done it

From pair gears
2-4-/6
And non pair gears
3-5-6

This can only be used to downshift,not upshift

08/20/2017 - 18:13 |
0 | 0

That horrible noise was your engine over revving and probably blew either the transmission or the engine itself. Don’t shift into the lower gear when you’re travelling on high velocity.

08/20/2017 - 18:47 |
0 | 0

Was hoping someone would catch the little hint in there. What that’s known as is a “money shift”….and I hope you can guess why, because you’ll need a lot of it after it happens!

08/20/2017 - 22:52 |
0 | 0
H5SKB4RU (Returned to CT)

My driving instructor told me that as long you go in order 2-4-6 or 3-5 while rev matching you should be fine, but the tranny may suffer more wear

08/20/2017 - 18:06 |
0 | 0
P5 Ford

You can skip gears, the engine nor transmission does not care as long as you rev match.

08/20/2017 - 18:27 |
0 | 0