Vortex Generators: How Do They Work?

The new Civic Type-R prototype didn't hold back on aero, with the addition of a Mitsubishi Evo-style spiked roof. So what is the function of these intricate fins?
Vortex Generators: How Do They Work?

The new Honda Civic Type R prototype revealed at the Paris Motorshow was one of the most exciting cars to be presented, with brutish and aggressive styling we all hope makes it to production. Of all the crazy aero bits though, one particular element caught our attention: the little lumps at the top of the rear windscreen. They are called vortex generators, which were most famously used before on the Mitsubishi Lancer Evolution, and have become a niche modification for aero-obsessed petrolheads out there.

To understand what benefits they bring to a car’s aerodynamics, we must first look at how airflow interacts with the moving body of a car. Due to friction between the solid surface and the air molecules passing over it, the air forms a fluid profile, with stationery air sitting at the meeting point between the fluid and the surface. This profile can also be called the boundary layer. The air speed then increases to what is called free stream velocity as the distance increases from the car’s body, as can be seen in the diagram below.

The air velocity increases as it gets further away from the bodywork
The air velocity increases as it gets further away from the bodywork

In terms of flow efficiency then, you want the air to be moving across the car as quickly as possible to avoid creating a large amount of friction, instead gliding smoothly over and away from the car. In terms of a car’s roof, the air is going to follow the curvature of the roof as much as possible, which is known as an ‘attached flow’.

So, bringing a rear wing into the equation, the ideal situation would be a nice attached flow that follows the entire roofline of the car and acts upon the wing, both increasing downforce and the wing’s overall aerodynamic efficiency.

Unfortunately, the airflow reaches a separation point somewhere around the end of the roof and diffuses off into free air space, leaving turbulent, slow-moving air to crash about the boot area meaning very little fluid flow ever makes it smoothly down to the wing. Factors like the rake of the windscreen and the curvature of the roofline have big implications on the characteristics of the airflow over the car and contribute to the placement of the point of separation.

The separation point can be seen clearly on the 300SL as the air stream leaves the roofline and flows proud of the rear window and boot
The separation point can be seen clearly on the 300SL as the air stream…

Although this separation point is inevitable, aerodynamic components like wings and diffusers can be optimised by controlling the distance at which the separation flow occurs. This can be achieved using - you guessed it - vortex generators.

To keep an attached flow going for as long as possible, you need high energy air. So, looking at the fluid profile, you want to get the high energy air from the top of the profile as far down and therefore as near to the car’s body as possible.

Remote video URL

What the vortex generator does is disturb the airflow running over the bodywork, producing a swirl of air in-between the high energy and low energy streams. This draws in a stream of high energy air from free stream down into the boundary layer, increasing the boundary layer’s energy. High energy air sticks to the bodywork much more effectively and therefore increases the attached flow.

Vortex Generators: How Do They Work?

This is the reason that – on cars – vortex generators are found spaced across the end of the roofline, exploiting as much of the high energy air as possible. On road cars however, the design of them is not the most efficient. On airplanes and Formula One cars, vortex generators are sharp-edged and often triangular to create the most effective vortex possible at very high speeds. But on mass-produced road cars, safety regulations dictate that they need to be smoothed-off and rounded which decreases their effect on the air flow, resembling much more of a purely aesthetic component than people may presume.

The vortex generators found on Torro Rosso F1 cars
The vortex generators found on Torro Rosso F1 cars

The efficiency of aerodynamic components generally increases with velocity, hence why F1 cars can justify exploiting vortex generators within their design, but the airflow passing over a normal road car – even on track – is normally just not quick enough. This is why rear wings are only really functional on a road car if they are positioned high enough from the body to intercept any high energy airflow. So the Civic may just get away with it considering its pronounced wing position, but the devices will only have a significant effect at very high speeds.

Have you modified your car to exploit vortex generators? And does the Evo-esque styling improve the look of the already bonkers Civic Type R? Comment below with your thoughts on the quirky little aero devices.

Sponsored Posts

Comments

Anonymous

Soooooo…. they do help???

10/10/2016 - 20:54 |
0 | 0
Manuel Kunz

In reply to by Anonymous (not verified)

If you have an F1 car, yes. If you have a normal roadcar, not really, since they have to be formed according to saftey regulations making them pretty much useless.

01/07/2017 - 01:39 |
0 | 0
Bring a Caterham To MARS

*Toro Rosso

11/06/2016 - 13:02 |
0 | 0
2jz_jc

Wait… Are you saying huge wings are good and better than lower wings????
Rice Master Pleb (black panthaa) would be proud to hear this.

01/07/2017 - 01:18 |
0 | 0
Anonymous

In reply to by 2jz_jc

90% of the race-style aero you see on streetcars is just useless weight. Body shape matters, but things like wings, cannards, and vortex generators are pretty much garbage because you don’t (shouldn’t) be driving fast enough on the street for them to kick in. On the highway, maybe, but then you don’t really need to handle sharp turns and it’s just adding weight and drag.
The only useful aero for a street car is getting it low, putting a solid belly-plate on it, a chin-spoiler and rear diffuser. Less/faster air under the car adds downforce while decreasing drag - improving fuel economy and handling at speed.

01/07/2017 - 08:09 |
0 | 0